GX5CrNiMo19-11-3 (EN 1.4412) Austenitic Stainless Steel Casting Material
Austenitic Stainless Steel
Introduction
GX5CrNiMo19-11-3 is an austenitic stainless steel casting grade covered by EN 10283, ISO 11972. Typical family applications include pump casings, impellers, valve bodies, covers and pipe fittings.
| Field | Value |
|---|---|
| Designation | GX5CrNiMo19-11-3 (EN 1.4412) |
| Material Type | Stainless Steel |
| Sub Type | Austenitic Stainless Steel |
| Product Form | casting |
Manufacturing Process
Investment Casting
Shell Molding Casting
Sand Casting
Equivalent Materials
Similar Materials
N/A
Reference Standards
Related Casting Products
Physical Properties
| Property | Value / Unit | Note | Source |
|---|---|---|---|
| Density | 7.9 kg/dm³ | Test at 20 °C | EN 10283 |
| Specific Heat | 530 J/(kg·K) | Test at 20 °C | EN 10283 |
| Thermal Conductivity | 14.5 W/(m·K) | Test at 50 °C | EN 10283 |
| Thermal Conductivity | 15.8 W/(m·K) | Test at 100 °C | EN 10283 |
| Thermal Expansion | 15.8 ×10⁻⁶/K | Temperature range: 20–100 °C | EN 10283 |
| Thermal Expansion | 17 ×10⁻⁶/K | Temperature range: 20–300 °C | EN 10283 |
| Thermal Expansion | 17.7 ×10⁻⁶/K | Temperature range: 20–500 °C | EN 10283 |
Chemical Composition
| Element | EN 10283Edition 2019 · wt.%Cast analysis | ISO 11972Edition 2023 · wt.% |
|---|---|---|
| C | ≤ 0.07 | ≤ 0.07 |
| Si | ≤ 1.50 | ≤ 1.5 |
| Mn | ≤ 1.50 | ≤ 1.5 |
| P | ≤ 0.040 | ≤ 0.040 |
| S | ≤ 0.030 | ≤ 0.030 |
| Cr | 18.00–20.00 | 18.0–20.0 |
| Ni | 10.00–13.00 | 10.0–13.0 |
| Mo | 3.00–3.50 | 3.00–3.50 |
| Cu | ≤ 0.50[1] | — / Not specified |
Notes
EN 10283 · Edition 2019
[1] Cu: Applies unless otherwise agreed; unspecified elements shall not be intentionally added without purchaser agreement except for finishing the heat.
Heat Treatment
EN 10283–2019 · +AT
| Step | Operation | Temperature | Cooling |
|---|---|---|---|
| 1 | solution annealing | 1120–1180 °C | water |
ISO 11972–2023 · Solution treated
| Step | Operation | Temperature | Cooling |
|---|---|---|---|
| 1 | solution treatment | 1120–1180 °C[1] | quench |
Notes
ISO 11972 · Edition 2023
[1] Solution treated: Depending on thickness, accelerated air cooling.
Mechanical Properties
Core Mechanical Properties
EN 10283 — 2019 · Table 2 — Normative
| Property | +AT |
|---|---|
| Yield Strength (Rp0.2) | ≥ 205 MPa |
| Yield Strength (Rp1.0) | ≥ 230 MPa |
| Tensile Strength | ≥ 440 MPa |
| Elongation | ≥ 30 % |
| Impact Energy | ≥ 60 J[1] |
- wall thickness ≤ 150 mm; Test block; maximum thickness 150 mm; Room temperature; Yield and tensile strength also apply to the casting up to the maximum specified wall thickness.
ISO 11972 — 2023 · Table 2 — Normative
| Property | Solution treated |
|---|---|
| Yield Strength (Rp0.2) | ≥ 205 MPa |
| Tensile Strength | ≥ 440 MPa |
| Elongation | ≥ 30 % |
| Impact Energy | ≥ 60 J[2] |
| Yield Strength (Rp1.0) | ≥ 230 MPa |
- wall thickness ≤ 150 mm; Room temperature; Test blocks used to verify mechanical properties shall not exceed 150 mm thickness. Properties for samples removed from castings shall be agreed between manufacturer and purchaser.
Notes
EN 10283 · Edition 2019
[1] Impact Energy: KV2 as specified in
ISO 11972 · Edition 2023
[2] Impact Energy: Verification of impact tests is required only when indicated by the customer.
Welding Conditions
EN 10283–2019
Notes
EN 10283 · Edition 2019
[1] Preheat: Preheat depends on casting geometry, thickness and climatic conditions.
[2] Post-weld Heat Treatment: minor welds; Air quenching may be agreed for very small, thin castings according to corrosion conditions.
[3] Post-weld Heat Treatment: major welds; Air quenching may be agreed for very small, thin castings according to corrosion conditions.
Applications
Typical applications for this corrosion-resistant steel casting family include components exposed to corrosive environments in general engineering service. Other cast components used in this material family include pump casings, impellers, valve bodies, covers and pipe fittings. Typical settings include chemical and pharmaceutical plants, food and beverage machinery, and filling, mixing and liquid-handling systems.
Need GX5CrNiMo19-11-3 Castings?
Contact us for casting and machining inquiries.
Email Us for a QuoteLast Updated: November 6, 2026